How to wire keypad to dmp panel

Updated Asked 3 times
Quick answer

Wire a DMP keypad bus red, yellow, green, and black to panel terminals 7–10.

Steps

From: DMP 2713, 8860, 8860POE Programming guid programming guide, p. 17

  1. Disconnect all power before wiring and observe polarity
    Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1
  2. Connect the harness to the keypad header
    Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1
  3. Connect the red wire to panel terminal 7 (power)
    Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1
  4. Connect the yellow wire to panel terminal 8 (send data)
    Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1
  5. Connect the green wire to panel terminal 9 (receive data)
    Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1
  6. Connect the black wire to panel terminal 10 (ground)
    Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1

Specs & limits

From: DMP 2713, 8860, 8860POE Programming guid programming guide, p. 17

NoteUse 18 or 22 AWG unshielded wire; do not use twisted pair or shielded wire on the keypad bus.
Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1
22 AWG keypad busdo not exceed 500 ft; 18 AWG: do not exceed 1,000 ft.
Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1
NoteMaximum length of any one bus circuit is 2,500 ft.
Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1
Panel power for 8860 keypadsXT75 up to five, XR panels up to four, XT30/XT50 one; extra keypads need an external power supply.
Source: DMP XR100 install guide · p. 15 Source: DMP 7000 Programming guide: 7000 Series programming guide · p. 1

Applies to

8860

Sources

  1. DMP 2713, 8860, 8860POE Programming guide: Document Discontinuance Notice (10/22/26) The 8860 7-Inch Touchscreen Keypad Installation (LT-2713), p. 17, p. 17
  2. DMP XR100 Installation guide: INSTALLATION GUIDE XR100 SERIES CONTROL PANEL MODEL XR100 SERIES CONTROL PANEL INSTALLATIO (LT-0899), p. 15, p. 15
  3. DMP 7000 Programming guide: 7000 Series Thinline™ and Aqualite™ Keypad Quick Start Guide This quick start guide walks (LT-2584), p. 1, p. 1
  4. DMP 2713, 8860, 8860POE Programming guide: Document Discontinuance Notice (10/22/26) The 8860 7-Inch Touchscreen Keypad Installation (LT-2713), p. 17, p. 17
Was this right?